<code id="sa0bz"></code>
    <th id="sa0bz"></th>

  1. <strike id="sa0bz"></strike>
      <strike id="sa0bz"></strike><del id="sa0bz"><small id="sa0bz"></small></del>
      <th id="sa0bz"><video id="sa0bz"></video></th>

      email: tony@lathes.co.uk
      Home   Machine Tool Archive   Machine-tools Sale & Wanted
      Machine Tool Manuals   Catalogues   Belts   Books  Accessories

      Naerok & Alpine Mill-Drills

      A Generic Manual & Parts List is available for this machine

      Typical of the generic Taiwanese-Korean "Mill/Drill" as made from the early 1970s and marketed by various companies worldwide including, in the UK, as Alpine, Sealey, Warco, Whitecote, Excel and Ajax, the example shown below branded "Naerok" (Korean written backwards) was certainly the best of the bunch. An almost identical model, with the electrical controls repositioned and a few very minor differences, was also sold branded as the "Alpine" - though some Alpine versions did lack the bevel gearbox fitted to the column elevation control.
      At 20" x 6.25", the table was unusually large with a useful longitudinal travel of 12.75" and in traverse of 5.5 inches. Satin-chrome-plated, zeroing micrometer dials were fitted at both ends of the table's longitudinal feed screw, these being engraved with divisions of 0.001". Although the table locking handles had proper spring-loaded ends - allowing them to be pulled out and repositioned on their splines -  they were made of plastic and so easily broken if over tightened
      The great advantage of the Naerok and Alpine - making them the least prosaic of the type - was the use of a bevel gearbox at the bottom of the column to elevate the head assembly, this playing in important part in the usefulness of the machine for, instead of the head being able to swing freely from side to side when the clamping bolts were slackened (as on all other makes), on the Naerok/Alpine the alignment was maintained through the whole of the vertical travel. The column was locked into the base casting by two handles that closed down a slot in the casting; the handles were usefully long and hinged so allowing them to be positioned so as to get a good purchase from almost any direction.
      In addition to the elevating head, the quill, which held either Bridgeport R8 or a No. 3 Morse taper spindle, could be moved through a travel of 3.5 inches by either a handwheel fine-feed control (working through worm-and-wheel gearing with each division on the micrometer dial being 0.002") or by a 3-spoke, quick-action capstan handle. Of the two tapers, the R8 is probably the preferred one, there being not only new but also limitless quantities of inexpensive used fittings such as collet sets, micrometer boring heads, direct-fitting collets and collets chucks etc. On the Naerok the spindle nose to table clearance is around 14 inches when fitted with the R8 taper (the spindle extends around 1.5 inches) so perhaps 15.5 inches on a No.3 Morse taper type.
      Power came from a rear-mounted, 1-phase 3/4 h.p. motor (other makers generally being fitted with ones between 1/2 and 1.5 h.p.) with drive by an "A" section V-belt from a 3-step on the motor to an intermediate, self-aligning, 4-step jockey pulley and then to a 4-step front pulley, the arrangement giving 12 speeds that spanned a most useful 90 to 2150 r.p.m. or, in some cases 110 to 1750 r.p.m. (other versions often had a higher bottom speed of 200 r.p.m. or so, together with a higher top speed of 2500 r.p.m., this arrangement making them handy for drilling and milling with small-diameter cutters - but less so for tapping). The motor was held on a plate, hinged on its left-hand side with tension applied to the belt by a simple push-rod on the right-hand side. The metal-to-metal contact of rod and plate can lead to rattles, the solution? Fit the rubber end from a walking stick over the end of the bar?br>A word of warning, the maker's spindle-speed figures for these millers are often slightly and sometimes very much out - it being possible that some were fitted with charts intended for the American and other markets where a 60 Hz electricity supply resulted in speeds some 20% higher than the UK's 50 Hz. The hinged pressed steel guard over the belt drive did leave something to be desired, being too flexible and with a nasty spring catch to hold it closed and a hopeless rubber ring around its periphery.
      A further advantage of the Naerok/Alpine was the availability of a very useful, infinitely-variable, auto-knock-off power longitudinal feed to the table. The unit was a third-party, Taiwanese-built type that was also offered for retro-fitting to other small milling machines and came with a very large, satin-chrome plated, clearly-engraved inch-division micrometer dial locked by a "non-upset", screw-action face-ring. This unit is still made today by various manufacturers and makes a handy addition to any small miller.
      Although inexpensive and of relatively crude construction - and with a less-than-perfect cosmetic finish - this type of mill/drill is a most useful addition to any workshop. Able to mill to tolerable accuracy with either large or small cutters, it becomes additionally handy when used as a coordinate drill - the vice being bolted securely to the table and the slides then manoeuvred to bring the workpiece exactly into the required location beneath the drill bit.
      Although the writer is reluctant to admit it - in case you think my opinion is infallible, which it is not - this is the mill/drill that I have in my home workshop and use for casual, odd-job milling and drilling work.

      High-resolution pictures - may take time to open

      A Naerok with infinitely-variable speed longitudinal power feed to the table

      One of the few "spoilers" - plastic handwheels

      Safety "no-Volt" release push-button starter

      Two-stage drive by A-section V-belts

      Not the rubber ferrule from a walking stick on the motor-tensioning plate

      The vice mounted on the table is a "Nippy" intended for drilling, a make that is no longer available
      but, with its handy vertically slotted and stepped jaws, is well worth seeking out second-hand

      Bevel gearbox for raising and lowering the head - while keeping it in alignment

      Robust, hinged locking levers to the column clamp

      The optional, third-party table power-feed attachment cam complete with a very large, inch-division micrometer dial locked by a non-upset face ring

      For an inexpensive machine, the micrometer dials were of a decent standard.

      Quill fine down-feed micrometer dial

      A Generic Manual & Parts List is available for this machine

      Naerok Mill-Drill
      email: tony@lathes.co.uk
      Home   Machine Tool Archive   Machine-tools Sale & Wanted
      Machine Tool Manuals   Catalogues   Belts   Books  Accessories